For aerial reticulating to residential, rural and uncleared areas where reliability, safety and low installation costs are required. Other benefits include: Reduction of bushfire hazards and frequency of tree lopping.

1.5 mm² Multicore with earth, V-90 PVC insulated and 5V-90 sheathed. According to AS/NZS 5000.1

1.5 mm² Multicore with earth, V-90 PVC insulated, 5V-90 bedded, SWA and 5V-90 sheathed. According to AS/NZS 5000.1

2.5 mm² Multicore with earth, V-90 PVC insulated and 5V-90 sheathed. According to AS/NZS 5000.1

2.5 mm² Multicore with earth, V-90 PVC insulated, 5V-90 bedded, SWA and 5V-90 sheathed. According to AS/NZS 5000.1

Underground residential distribution (URD) cable is typically installed up to the point of supply to residential dwellings.

Underground residential distribution (URD) service cable is used as final supply to residential dwellings.

Our power distribution cables are designed and developed according to various local ratings and requirements.

A range of self-supported aerial telephone copper cables featuring integral bearer wire and Dry Core.

Afumex is a range of halogen free flame retardant cables, which saves lives and money in case of a fire. Gone is the black poisonous smoke, as is the corroding substances that ruin electronics and machines. Remaining is the flexible properties that make the cables so easy to install. Cables can be the means of propagation of a fire from one room to adjacent rooms and the majority of deaths in a fire are due to inhaling dangerous gases, not the…

Terminate the rat battle with heavy armour. Our all-dielectric ARM@CORE fibre optic cables are fully protected against ruthless New Zealand rodents. Despite the solid hardware these loose tube cables are still surprisingly lightweight, flexible and easy to handle. The Prysmian ARM@CORE cable uses glass reinforced plastic (GRP) rods to fully armour the cable and offer the robust protection needed to block rodents and polyamide provides anti-termite protection. Furthermore, the cable uses SM@RTCORE reduced diameter technology and offers a rodent proof…

Overhead conductors in common use around Australia and are available in all aluminium, aluminium alloy, copper and galvanised or aluminium clad steel constructions.

MaxCap-BB-OMx combines two of our industry-leading technologies: MaxCap high bandwidth multimode fibre and BendBright bend-insensitive single-mode optical fibre technology. MaxCap-BB-OM2 / OM2+ / OM3 / OM4 optical fibres support compact cable management. This new class of MaxCap multimode fibre combines the support of improved fibre management, with high bandwidth 10G – 40G – 100G system requirements. Improved flexibility for MACs (Moves, Adds, Changes) applied in Local Area Network (LAN) backbones up to 550m (10GBASE-SX), in Data Centres up to 170m…

The CLICK-FIT® plug-in concept is a unique system designed to connect high and extra-high-voltage extruded power cables for 72 kV up to 420 kV. Important features are high reliability combined with fast, easy and man-independent installation techniques that lead to a reduction in project realization time and cost. Following the principle of the CLICK-FIT® concept, the ends of the cables are prepared and provided with plugs. The uniform plug design enables the installation of joints and terminations simply by plugging-in…

Solid PACW, PVC insulated, max resist 94.5, capacitance unbalance max 300/500 m @ 800 hz.

Copper and FO data control cables for use in fixed and flexible installations. Designed for data transmission in low and high temperatures in accordance to various standards.

The Corrugated Steel Tape Armoured cable is designed for external underground installations in ducts or by direct burial. Corrugated steel tape provides rodent protection and polyamide provides anti-termite protection. The armoured structure also provides additional compressive strength for the cable. Use this type of optical cables when you want maximum crush resistance. For a more detailed description, please download our datasheet(s) / brochure. Alternatively our contact details are listed below if you wish to speak to a Prysmian Product Specialist…

ECOSPEED™ cold shrink joint for Um up to 36 kV polymeric cables. For armoured cable, please contact us for further information.

We are an expert in power, control, instrumentation and signal cables for use in onshore applications such as petrochemical plants, refineries and LNGs. In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

We specialise in power, control, signal and instrumentation cables designed primarily for use in offshore & marine applications (production and drilling).In order to meet different standards and conditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

We have the full range of communication cables used in production and drilling applications both offshore and onshore (pipelines, refineries and petrochemical plants). In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Down well hole extraction systems are the main artery of crude oil production. The reliability of electrical down well pump systems is directly dependent on the performance of the power feed through to the wellhead, power cable, motor lead cable, pig tail connectors and related equipment such as the pump and motor. These cables offer: efficiency, ruggedness, handling flexibility, ease of installation and maintenance, reliable performance. They are able to withstand high temperatures and harsh environments and possess high resistance…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Prysmian has led the field with technology-driven products for oil, gas and geothermal wells. We can cater to tubing encapsulated cable, specialty tubing and specialty optical-fibre sensing cables. In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

The most common applications of submarine cables in power transmission and distribution systems are: electrical feeding of islands from the mainland or a major island of an archipelago, interconnections between HV networks for possible transfer of electrical power in both directions, transfer of cheap power generated on natural or artificial islands to the mainland, crossing of sea inlets and rivers, connection to or between offshore oil production facilities and transmission of power from renewable offshore sources. In order to meet…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Extruded cables are light and easy to handle and extruded cable systems are designed to be maintenance-free. Dependent on the system requirements, these features present significant benefits in terms of total installed system cost. Prysmian produces extruded cables with either XLPE or EPR insulation material, using design and process technologies, which ensure continued service reliability and long-term performance. Such cables can operate at elevated temperatures and under considerable electrical stress. Prysmian also offers a wide range of accessories for extruded…

The extruded dielectric offers many advantages that make the cables lighter and easier to handle and to install. Both EPR and XLPE can be used for insulation: they provide the cables with the advantage of operating at high temperatures (90°C) and at high electrical stresses. In most cases, XLPE requires an impervious metallic sheath (e.g. lead sheath) to be applied over each core to avoid direct contact with water. EPR compounds can be formulated in such a way as to…

The extruded dielectric offers many advantages that make the cables lighter and easier to handle and to install. Both EPR and XLPE can be used for insulation: they provide the cables with the advantage of operating at high temperatures (90°C) and at high electrical stresses. In most cases, XLPE requires an impervious metallic sheath (e.g. lead sheath) to be applied over each core to avoid direct contact with water. EPR compounds can be formulated in such a way as to…

The extruded dielectric offers many advantages that make the cables lighter and easier to handle and to install. Both EPR and XLPE can be used for insulation: they provide the cables with the advantage of operating at high temperatures (90°C) and at high electrical stresses. In most cases, XLPE requires an impervious metallic sheath (e.g. lead sheath) to be applied over each core to avoid direct contact with water. EPR compounds can be formulated in such a way as to…

We have a comprehensive and specialized program of pre-fabricated fibre cable kits. Choose between customized solutions and accessories, for within or between towers and grid connection.

We have a comprehensive and specialized program of pre-fabricated fibre cable kits. Choose between customized solutions and accessories, for within or between towers and grid connection.

All our Fire Resistant cables are also available in a NON-FIRE RESISTANT construction with NO FIRE RESISTANCE properties (no Mica glass tape for fire barrier). These are still LS0H, flame/fire retardant and meet all requirements of IEC 60332-1 and IEC 60332-3.

Fire rated, flexible multicore LS0H cable suitable for installation wiring.

Fire rated, flexible single core LS0H cable suitable for installation wiring.

Fire rated fire alarm circuit LS0H cable suitable for installation wiring.

Fire rated multicore LS0H cable suitable for installation wiring.

Fire rated, single core LS0H cable suitable for installation wiring.

Fire rated fire alarm circuit LS0H cable suitable for installation wiring.

Fire rated multicore LS0H cable suitable for installation wiring.

Multicore Flexcords Ordinary Duty – 250/440V compliant with AS/NZS 3191 and regulatory requirements for Flexible Cords.

Indoor drop optical fibre cable with steel wire reinforcement and LSOH sheath. Designed to run from the distribution point to the subscriber, in both home and business premises.

The Prysmian name has been synonymous with fluid filled High Voltage cable systems since it invented and introduced its range of products into service in the 1920s. With their proven electrical performance, life expectancy and excellent reliability record, these type of cable systems continue to meet the ever increasing demands of the world-wide transmission and distribution systems up to 1100 kV AC. With its long experience in the design and production Prysmian offers its own comprehensive range of High Voltage…

This series is part of the most deployed fibre type worldwide and can be used in all cable constructions including loose tube, tight buffered, ribbon and central tube designs. We offer two types, standard and enhanced. The enhanced Single-Mode Fibre (ESMF) is compliant with ITU-T Recommendation G.652, Table D. The tighter geometrical, attenuation and PMD specifications of the enhanced type enables superior performance in long haul, metropolitan, access and premises applications for telecommunications, CATV and utility networks.

Long distance and metropolitan non-zero dispersion shifted fibres developed for optimized dispersion characteristics in high-capacity, long-distance networks. Our TeraLight® fibre is available in 2 versions, the regular TeraLight® and the TeraLight® Ultra. The benefit of the former is the minimization of your chromatic dispersion compensation while the latter is optimized for ultra-long transmission. Both versions offer: • Solutions for long haul and metropolitan transmissions. • Excellent distortion management. • Cost effective operation at 10 and 40 Gbps. • Tight channel…

We believe that bend-insensitive optical fibres shouldn't have to come at the expense of other characteristics. In order to enhance the world's most deployed single mode optical fibre, the G.652 standard, Prysmian invented the BendBright® family comprising of BendBright® and BendBrightXS. They have a bend sensitivity reduction of x10 and x100 respectively as compared to G.652 without compromising on quality. Important features of the BendBright® family: • Compliance with the most stringent ITU-T G.652.D recommendation. • Capacity for tighter, high-end…

A rugged cable, offering a high level of mechanical and environmental protection whilst enabling easy breakout and fibre termination within multi-dwelling or office buildings. This tight buffered multi-cord optical cable is suitable for applications in local area network (LAN) including FDDI cabling, Ethernet and Token ring. For a more detailed description, please download our datasheet(s) / brochure. Alternatively our contact details are listed below if you wish to speak to a Prysmian Product Specialist for further information.

High-temperature conductors for overhead lines allow an upgrade of the existing line, guaranteeing a more convenient solution in terms of total cost of ownership The high-temperature conductors for overhead lines are especially designed to solve the problem related to the construction of new lines due to lack of available lands, difficulties to get permissions and environmental restrictions. The conductors allow an upgrade of the existing line increasing the ampere capacity from 1.5 to 2 times by replacing only the conductors,…

HSE EXTRA@CORE® is a frontier fibre cables breaking new ground. Our latest test equipment brings trial and error to a completely new level, replicating forces only found in the most hostile environments. The first result, HSE EXTRA@CORE®, was above all expectations. It’s the toughest direct burial High Strength cable yet. The HSE EXTRA@CORE® is qualified using enhanced Axial Compression Resistance (ACR) test method. It’s small, lightweight and available in lengths up to 10.5 km. All these features adds up in…

AC transmission is used on short distances because it is more cost effective as it does not require converter stations. HVAC cables are either extruded or paper insulated. Prysmian cables insulation technologies are suitable for voltages up to 1000 kV AC.

HVDC cable systems are the most viable solution for power transfer between asynchronous networks, crossing of large water bodies and long distance transmission lines also in hybrid configuration. In meshed AC networks HVDC systems provide controllable bulk power transmission capacity without increase in short circuit current levels.

Made for the distribution of optical fibre cables within the Multi-Dwelling Unit (MDU) or office buildings. This tight buffered multi-fibre optical cable is suitable for applications in local area network (LAN) including FDDI cabling, Ethernet and Token Ring. This cable is suitable for light loads. For a more detailed description, please download our datasheet(s) / brochure. Alternatively our contact details are listed below if you wish to speak to a Prysmian Product Specialist for further information.

Ferrule assembly for (LC compliant) connectors is a new compact pre-connectorized system, which can be used within ducts of very small size or can be blown into micro ducts, offering an easy and reliable solution to perform FTTx installations. After installation, the ferrule assembly can easily and rapidly be connectorized, avoiding time-consuming and expensive field termination tools and equipment.

Ferrule assembly for (LC compliant) connectors is a new compact pre-connectorized system, which can be used within ducts of very small size or can be blown into micro ducts, offering an easy and reliable solution to perform FTTx installations. After installation, the ferrule assembly can easily and rapidly be connectorized, avoiding time-consuming and expensive field termination tools and equipment.

Large Multi-function Joints (LMJ) are for jointing of optical fibre cables up to 1344 fibres (with option to double capacity using 24 fibre single element trays). Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S…

Underground, solid PACW, solid PE insulated, PE sheathed. Available with an optional Nylon Termite Resistant Jacket. ACMA approved.

Applying our many years of expertise and global capabilities, we offer one of the world's most proven and comprehensive product ranges for wind power generators.

For the connection from the generator to the transformer down the tower we can offer several low voltage cables depending on your needs. They are fully optimised for twisting at high and low temperatures in accordance to various standards.

These cables are presently suitable for voltages of up to 500 kV DC. The insulation consists of high-density paper tapes impregnated with a high-viscosity compound, which does not require fluid pressure feeding. These cables can be installed in high voltage DC links in very long lengths, up to several hundreds of kilometres. Present experience or trials are limited to water depths in the range of 1000 m, but deeper waters can be reached by using special design features. We tailor-make…

These cables are presently suitable for voltages of up to 45 kV AC. The insulation consists of high-density paper tapes impregnated with a high-viscosity compound, which does not require fluid pressure feeding. These cables can be installed in HVDC links in very long lengths, up to several hundreds of kilometres. Present experience or trials are limited to water depths in the range of 1000 m, but deeper waters can be reached by using special design features. We tailor-make your solutions…

These cables are presently suitable for voltages of up to 45 kV AC and 500 kV DC. The insulation consists of high-density paper tapes impregnated with a high-viscosity compound, which does not require fluid pressure feeding. These cables can be installed in links in very long lengths, up to several hundreds of kilometres. Present experience or trials are limited to water depths in the range of 1000 m, but deeper waters can be reached by using special design features. We…

Medium Multi-function Joints (MMJ) are for jointing of optical fibre cables up to 288 fibres. Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S risks and negates risk of fires. Not only are the new…

Our specialization in MV cable systems has led to the development of a comprehensive range of medium voltage accessories.

For the transmission of power from 6 kV up to 55 kV, we offer single and four core medium-voltage flexible cables. They are optimised for torsion twist in the tower down to -40 °C.

Our specialization in MV cable systems has led to the development of a comprehensive range of medium voltage accessories.

Our FORMFIT range of MV separable connector are suitable for a wide range of applications, including connection of cable to i.e. transformers, switchgear units, motors and cable to cable. Suitable for indoor and outdoor installations, the connectors are entirely protected by a watertight conductive envelope connected to earth.

The key features of these Prysmian products are absence of impregnating fluids and/or pressure feeding requirements, reduced cable weight and dimensions as well as relative ease of jointing. MV submarine cables can be either EPR or XLPE insulated. In most cases, XLPE requires an impervious metallic sheath (e.g. lead sheath) to be applied over each core to avoid direct contact with water. EPR compounds can be formulated in such a way as to give an excellent performance in terms of…

Suitable for ISDN and DSL applications. Internal telephone cable for 2 Mbit/s rate and 120 ohm @ 1 MHz. 1/0.5 PACW, polyolefin insulated, twisted pair, aluminium/laminate screen with a 1/0.50 mm tinned annealed copper drain wire, LSOH thermoplastic sheathed, ACMA approved. Off-white coloured sheath.

A range of Local Area Network (LAN) copper cables, with specifications to meet the requirements of Category 5E and 6. Mega 5e 1/0.5 mm 24 AWG PACW, polyolefin insulated, twisted pair, flame retardant PVC sheath (75°C). UL Listed. Nominal impedance 100 ohm. Tested up to 100 MHz, (tested up to 450 MHz on request). Velocity of propagation 67%. Blue Sheath. CommandLinx 6 1/0.57 mm 24 AWG PACW, polyolefin insulated, twisted pair, flame retardant PVC sheath (75°C). UL Listed. Nominal impedance…

A range of telephone copper cables for both internal and external use with specifications to meet requirements up to Category 3. M@XTEL® internal Cat3 cable 3. 1/0.50 PACW, polyethylene insulated, twisted pair, unit construction, polyester core wrapped, PVC sheathed, ACMA approved. Cream coloured sheath.  

M@XTEL® external Cat3 cable 1/0.50 PACW, polyethylene insulated, twisted pair, unit construction. Jelly filled, core wrapped, PE sheathed. ACMA approved.M@XTEL® external cable unscreened Solid PACW, cellular PE insulated, unit twin construction. Jelly Filled, core wrapped, PE sheathed. ACMA approved.M@XTEL® external Cat3 cable 1/0.50 PACW, polyethylene insulated, twisted pair, unit construction. Jelly filled, core wrapped, PE sheathed. ACMA approved.M@XTEL® external cable screened with moisture barrier Solid PACW, cellular PE insulated, unit twin construction. Jelly Filled, core wrapped, PE sheathed. ACMA approved.

Our new rodent proof, all dielectric fibre optic cable NoR@T is designed to withstand aggressive NZ rodents. With a protective layer of Glass Reinforced Plastic (GRP) the cable is small, lightweight and flexible – and still impenetrable.

Multimode fibres are intended for all applications where the distances covered are short, such as Local Area Networks (LAN) or all networks with a small reach like campus, buildings or offices. OM1 fibre will support link lengths greater than 400 meters at 850nm and 1000 meters at 1300nm in LAN applications. A multimode fibre also enables connections for backbone, riser and horizontal links. All these networks are characterised as having many points of access to the fibre and the short…

Multimode fibres are intended for all applications where the distances covered are short, such as Local Area Networks (LAN) or all networks with a small reach like campus, buildings or offices. OM3 fibre will support link lengths greater than 1000 meters at both 850nm and 1300nm in LAN applications. A multimode fibre also enables connections for backbone, riser and horizontal links. All these networks are characterised as having many points of access to the fibre and the short distances covered.…

WideCap-OM4 multimode fibre delivers OM4 performance in the 850-950nm window while maintaining compatibility with current multimode fibres. Traditional OM4 fibres offer high bandwidth in a narrow band centred at 850nm. To satisfy the exponentially increasing information demand in Data Centers, the capacity of WideCap-OM4 has been extended to longer wavelengths up to 950nm. WideCap-OM4 and multi-wavelength transceivers are a viable solution for future 100 and 400Gbps multi-wavelength systems. WideCap-OM4 incorporates BendBright® technology to withstand tight bends and cabling challenges in the data centre.

The communication cable OptiC@t™5e is a combo of a four pair Cat 5E and two bend-insensitive fibres. Not only will it’s capability for super high-speed make the building attractive to future owners, the Low Smoke Zero Halogen sheath makes the building much safer, too. Plus, the cables insensitivity to bending makes it a lot easier and less expensive to install. Copper and optic fibre links the present to the future and gives you the better of two worlds. Are there…

PPL cables use a special low permittivity - low loss insulation type. Compared to conventional self-contained fluid filled paper insulated cables at the same power, it allows for increased transmitted power or reduced conductor size and cable dimensions. The use of PPL is in general considered for large sizes and for voltages above 275 kV. We tailor-make your solutions In order to meet different standards and preconditions we always tailor-make the cable systems in this area. Please contact our experts…

PRY-CAM is an integrated portable instrument for automatic acquisition, processing and classification of pulse signals generated by Partial Discharge (PD) phenomena occurring in insulating materials of medium and high voltage electrical systems and components. Wireless PRY-CAM allows accurate diagnostic measurements and continuous monitoring without having to switch off the electrical system during the test.

Pry-Mould accessories are based on pre-moulded electrical components, i.e. stress cones for terminations and one-piece sleeves for joints. Pre-moulded sleeves and stress cones are currently available for HV polymeric cables from 72.5 kV up to 525 kV and adopt the same design at all voltage classes.

Prysmian is the world’s largest producer of top-notch cables, covering all angles of the railway enterprise. On every continent, our cable solutions sit at the heart of significant railway projects. As your one stop shop, we provide you with a full market offer – everything from power, signalling to data and telecom. Furthermore, we can provide you with all the services you might need – before, during and after.

If you are looking for a system that can be easily deployed in an existing duct, sub-duct, directly buried or aerial infrastructure, then Prysmian’s RETRACTANETXS solution meets the challenge. In settings such as residential (brownfield or greenfield sites), rural and aerial applications, the RETRACTANETXS solution is fast, flexible, reliable and userfriendly. A combination of a fully integrated connectivity solutions and a full suite of innovative tools allows for efficient and effective installation practices, delivering a reduced Total Cost of Ownership. The unique RetractaCable, filled…

Ribbon Fibre Cables offer extremely high fibre density as well as the advantages of Mass Fusion Splicing - where 12 fibres can be fusion spliced in one operation. This has the potential to speed up network roll out and significantly cut splicing and installation costs. Prysmian is the only cable supplier manufacturing fibre ribbons in Australia, these are supplied in a range of fibre count cables from small 72 fibre cables to high capacity 864 fibre cables. Designs up to…

These cables are presently suitable for voltages up to 600 kV DC. They can be laid at depths down to approximately 800 m without special precautions; with the use of special fluids and proper armour designs, depths of 2000 m can be reached. The cables designs depend on the feeding length – maximum connection lengths are between 60 to 100 km, depending on system features. The longer the route, the larger the oil duct required. We tailor-make your solutions In…

These cables are presently suitable for voltages up to 1000 kV AC. They can be laid at depths down to approximately 800 m without special precautions; with the use of special fluids and proper armour designs, depths of 2000 m can be reached. The cables designs depend on the feeding length – maximum connection lengths are between 60 to 100 km, depending on system features. The longer the route, the larger the oil duct required. We tailor-make your solutions In…

These cables are presently suitable for voltages up to 600 kV DC and 1000 kV AC. They can be laid at depths down to approximately 800 m without special precautions; with the use of special fluids and proper armour designs, depths of 2000 m can be reached. The cables designs depend on the feeding length – maximum connection lengths are between 60 to 100 km, depending on system features. The longer the route, the larger the oil duct required. We…

By tailoring our product range to our customers requirements we believe that we as cable makers are taking an important step towards supplying cabling solutions that will have a decisive impact on increasing our customers’ profitability.

Class 5 copper conductor. R-E-110 insulated, HFS-110-TP sheathed to AS/NZS 5000.1

Our new Singlesm@rt cable uses a unique cable design of composite glass fibre reinforced plastic (GRP) strength member laid in parallel to loose tube,  thus eliminates fillers found in a traditional multi loose tube design. This design provides a small and extremely cost effective cable with tensile and crush strengths comparable to the larger traditional loose tube design. The loose-tube contains up to 24 single-mode fibres and is filled with a low viscosity, non-melting gel that prevents the longitudinal passage…

The cable complies with the requirements of 2 Pfg 1169/08.2007, Fire Performance: IEC60332-1, Smoke Density: IEC61034, EN50268-2, Halogen Acid Gas Emission: IEC60754-1, EN50267-2-1, Certificate: TUV.

This tight buffered single cord optical cable is specifically designed for use in the last leg of the Fibre To The Premises (FTTP) applications. The cable can be pre-connectorised and protected with QUICKDR@W pulling shroud for ease of installation and without the use of expensive fusion splicing equipment. It is specifically designed to be flexible and kink resistant. For a more detailed description, please download our datasheet(s) / brochure. Alternatively our contact details are listed below if you wish to…

The SM@RTCORE® Lite optical cables consist of a single filled loose tube containing up to 12 individually coloured optical fibres. The tube is centrally positioned and surrounded with high absorption performance water swellable yarns for water blocking. The cable is sheathed with polyethylene and jacketed with integrally bonded UV stabilised nylon. The nylon jacket acts as a protective layer against termites and ants. The sheath is UV stabilised Low Smoke Zero Halogen (LS0H), low smoke and fume thermoplastic in compliance…

4.0 mm² to 10 mm² 3 core plus 3 split earth, XLPE insulated and 5V-90 PVC sheathed to AS/NZS 5000.1 incorporating a copper tape screen over 5V-90 PVC bedding.

The cable is armoured using one layer of galvanized round steel wires (GSW). The GSW provides mechanical and rodent protection. This armoured optical cable is designed for external underground installations. Heavy protected. Designed for installation in areas where mechanical impact is expected. For a more detailed description, please download our datasheets / brochure. Alternatively our contact details are listed below if you wish to speak to a Prysmian Product Specialist for further information.

We can offer you high-end submarine cables for all common applications of submarine power transmission and distribution systems. That includes everything from the connection to or between offshore oil production facilities and transmission of power from renewable offshore sources to electrical feeding of islands.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Indoor/outdoor cold shrink termination for polymeric cables up to 36 kV.

When the transition between a fluid-filled cable and a XLPE cable is required, a very specific jointing solution has to be used. Such a solution is designed to ensure the proper connection between the different cable designs and to guarantee an adequate sealing to avoid any leakage from the paper insulated side. We can offer a wide range of three-core transition joints depending on the specific circuit requirements.

Twisted pair or triple, V90-HT insulated, Al/polyester overall screened with drain wire, black PVC 5V-90 sheathed.

Twisted pair or triple, V90-HT insulated, element and overall Al/polyester screened with drain wire, black PVC 5V-90 sheathed.

Designed specifically for bringing optical fibre directly to residents of high and low rise apartments and offices, the heart of the VertiCasaXS system features a new concept in optical cable construction allowing remarkably easy fibre access and break-out, reducing the demand for skilled labour and installation time and cost. The VertiCasaXS system provides a fast and flexible means of connecting users in a Multi Dwelling Unit (MDU). The system comprises a main riser cable of up to 144 fibres, which…

4.0 mm² to 10 mm² 3 core plus split earth, X-90 XLPE insulated and 5V-90 PVC sheathed to AS/NZS 5000.1 incorporating a heavy duty tinned copper braid screen over metallised tape.

1.5 mm² and 2.5 mm² 3 core, X-90 XLPE insulated and 5V-90 PVC sheathed to AS/NZS 5000.1 incorporating a heavy duty tinned copper braid screen over metallised tape.

Prysmian offers an extensive range of MPO/MTP® trunk cable assemblies suitable for all data centre applications. Features and Benefits Type A, B and C available MPO-8, MPO-12, and MPO-24 Base Low Loss performance MPO-F to MPO-F or MPO-M to MPO-M MPO Method A and Method B available Compatible with Type-P MPO-LC Module Female (Standard) & Male MPO/MTP Connectors Small diameter 3.0mm for MPO-8 and MPO-12, 3.8mm for MPO-24 Factory Terminated and Tested Lightweight High Density ANSI EIA/TIA 568-C .3 ISO/IEC…

Prysmian offers an extensive range of optical patchcords. All patchcords are fully qualified to Telcordia GR326 and IEC 61300 and all materials used are RoHS compliant. Patchcords can be supplied in a variety of lengths and with a variety of different connector types. Different fibre types and cable diameters are also available on request. Hybrid patchcords with different connector types on each end are also available. Please contact Prysmian for further information. Note: For the 96f/192f/288f - 1RU/2RU/3RU SRS4000 patch…

Prysmian offers an extensive range of optical pigtails. All pigtails are fully qualified to Telcordia GR326 and IEC61300 and all materials used are RoHS compliant. Size and length of standard pigtails are listed below. Pigtails can also be supplied in a variety of lengths, colours and different connector types for other applications and products. A part number builder is also given below to provide codes for other pigtail configurations. Features and Benefits Full traceability and test certification supplied with each…

Our Sm@rtspan series of all Dielectric Self Supporting cables are very strong in order to withstand wild weather and heavy wind loads. The most important benefits with our Sm@rtspan® series are: • Strong to minimize cable sag, even for large spans. • Compliant with industry standard fittings so that you don’t need any special training to secure the cable. • Not containing any metallic elements, which makes the cable unaffected by electromagnetic fields. • Can be installed on low, medium…

The SRS4000 Distribution Sub-Rack is a modular sub-rack available in a variety of configurations for integration into 19” / ETSI / ANSI racks, street-side cabinets or wall mounted cabinets. The product consists of a metal chassis available in 1U, 2U and 3U into a which a choice of modules are loaded. The module types available are Splice and Patch, Patch Only, Splice Only, Patchcord Storage and Connectorised Splitter. This allows users to customise the product for different applications whilst using…

UCCONNECT® UC9500 series Light Weight Fibre Suite is designed for the use in the Entrance Room, Horizontal Distribution Areas and Equipment Distribution Areas in the exchange offices or date centres. The UC9500 Series Standard Patch Panels consist of a 1.2mm thickness steel chassis that can mount to standard EIA 19" rack rails. The products have sleek design and feel, water painted surface, abrasion resistance and highly durability. Each 1U unit has 4 slots to be equipped with either modular adaptor…

UCCONNECT® UC9600 series Ultra High-Density Patch Panel is designed to address all the fibre termination and patching requirement for hyper scale date centres. The chassis consist of cold-rolled steel and aluminium to balance the robust and light weight. They can be installed into 19” / ETSI / ANSI racks. The products have sleek design and feel, anodized surface, abrasion resistance and highly durability. Each 1U unit has 6 sliding slots to be equipped with modular 24F cassettes providing up to…

The Adaptor Face Plates kit are fitted into the 1, 2 or 3U SRS4000 Splice and Patch Shelves. Each Adaptor Face Plate fits half of 1U. The Adaptor Face Plates can be used to install into an unconfigured Splice and Patch Shelf or can be used to upgrade an existing shelf. Kit Contents The kit comprises of an adaptor faceplate and adaptors. Single-Mode Patch Upgrade Kits (Adaptors + faceplate) Code Description Adaptor Colour XSRSC00145 SC/UPC 12f Duplex S/ mode Blue…

Our Sm@rtspan series of all Dielectric Self Supporting cables are very strong in order to withstand wild weather and heavy wind loads. The most important benefits with our Sm@rtspan® series are: • Strong to minimize cable sag, even for large spans. • Compliant with industry standard fittings so that you don’t need any special training to secure the cable. • Cable doesn’t contain any metallic elements making it impervious to electromagnetic fields. • Can be installed on low, medium and…

UC9500 Splice Tray and Cover keeps the fusion splices away from accidental stress-strain, water droplets and dust particles. Features and Benefits Stackable with detachable cover High quality fingerprint and dust resistant surfaces Light weight and highly durable 24F version does not include splice protective tube 48F version include splice protective tube Compatible with UC9500 Series Stackable up to 2 splice tray per one RU

UC9600 Ultra High-Density Module Cassettes are designed specifically to fit the UC9600 series Ultra High-Density Patch Panel providing various configurations for the hyper scale date centres applications. Features and Benefits  Available in Duplex LC or Uni-boot LC patch cord Available in G657A, OM3 and OM4 Utilises bend-insensitive fibre Plug & Play Installation Quick release mechanism MPO/MTP® Cassette available with 3xMPO-8, 2xMPO-12, 1xMPO-24 Type P (Pair-Flipped) is Draka UC defacto (compatible with Type-B MPO(F) to MPO(F) Trunk Cable), Type A and…

The SRS3000 Patchcord Storage Shelf is a 1U shelf used for the storage of patchcords or the storage of patchcord overlength. The shelf can be installed in to 19” / ETSI / ANSI racks, street side or wall mounted cabinets. The product consists of a metal chassis and a plastic light weight module. The product has a capacity of up to 48 patchcords in a 1U unit. Features and Benefits Suitable for installation into 19”, ETSI and ANSI racks. Can…

Prysmian offers a range of Front-Panels compatible with UC9500 Fiber Patch Panel Series. Features and Benefits Cold rolled steel Plate, thickness 1.2mm Powder Coating (water mark) Easy snap latches fixtures 6x port per panel Gongs nails to firmly secure the adaptors Blank panel is available Adaptor available in below options Multimode and Singlemode LC Duplex or Quadplex SC Simplex or Duplex FC Simplex ST Simplex MPO or MTP® Type A or Type B MPO-8, MPO-12 and MPO-24 Base compatible

The Horizontal Routing and Storage Shelf is a 3U shelf used to transport patchcords from one side of a 19” or ETSI rack to the opposite side. The shelf can also be used as a patch cord storage shelf for the storage of patch cord over-lengths. Manufactured from the steel, the shelf contains two routing mandrels for the coiling of the patch cord over-lengths. The shelf fits directly into 19” racks and cabinets and can also be mounted into ETSI…

UC9500 Module MPO/MTP® LC-Duplex is designed specifically to fit UC9500 Patch Panel. Design and engineered to reduce total cost of ownership when deployed with 12-Fibre MPO-MPO, or 12-Fibre MTP®-MTP® fibre trunks. This module supports the popular 2-fibre 10Gb up to the next generation 25Gb/40Gb/100Gb/400Gb applications. MTP® is a registered 12-fibre MPO connector, trademark of USCONEC. Features and Benefits Installed with Draka BendBright®-XS bend-insensitive fibre Installation is simple, with the module being easily installed, or removed, using push-pull mechanism, no tools…

Choose between high quality cables in copper or aluminium, single or three core, light or heavy duty screened, armoured or unarmoured, PVC, High Density Polyethylene or Low Smoke Zero Halogen sheathing.

Compact Multi-function Joints (CMJ) are for jointing of optical fibre cables up to 144 fibres. Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S risks and negates risk of fires. Not only are the new…

Compact Multi-function Joints (CMJ) are for jointing of optical fibre cables up to 144 fibres. Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S risks and negates risk of fires. Not only are the new…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements. Our reference projects

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Copper conductor, V-90 PVC insulated and 3V-90 PVC sheathed. According to AS/NZS 5000.2

0.6/1 kV Building wires and earths, copper conductor, V-90 PVC insulated, unsheathed. According to AS/NZS 5000.1

It’s when the flames consume everything around them and the heat becomes intolerable that our fire-resistance cable, Firestop™, displays its best qualities. In intense heat conditions this low smoke zero halogen cable continues to supply all the critical functions such as fire alarm, emergency lighting and fans. Fully complying with the latest New Zealand standard AS/NZS 3013. This range is designed to save lives and help protect property in the event of a fire. FS110, copper conductor, Mica glass taped,…

Our size-reduced, waterproof SM@RTCORE® range of fibre optic loose tube cables saves you space, time and money. It’s easier to install and you can increase the number of fibres in a duct, lower the number of ducts needed or extend the life of existing ducts. Plus, the strong, still smooth, polyethylene/nylon sheath protects against termites and reduces friction. With duct space becoming an increasingly sought after commodity, the new cable offers many advantages to network owners. SM@RTCORE® is manufactured with…

Class 2 compacted copper or aluminium conductor, X-90 XLPE insulated, 5V-90 PVC sheathed. According to AS/NZS 5000.1

Our new CableMate® – always there when you need it. A real mate is someone to rely on when times are tough. So is our new compact CableMate®. Only 80 cm high when folded, but strong as few when you need a helping hand with a 500 metre reel of flats or orange circulars. Not only does it save your back – it also makes your everyday work more simple, comfortable and installations faster. What more can you ask from a real workmate?…

Our Minism@rt cables present the next stage in fibre optic cable deployment. Using state of the art manufacturing technology and process control, Prysmian has drastically miniaturised loose tube cables, offering benefits to both installers and network owners. This radical reduction in cable cross-section leads to high fibre-density cables, significantly increasing duct utilisation. This offers the potential to increase the number of fibres in a duct, lower the number of ducts needed or extend the life of the existing infrastructure, all…

Choose between high quality cables in copper or aluminium, single or three core, light or heavy duty screened, armoured or unarmoured, PVC, High Density Polyethylene or Low Smoke Zero Halogen sheathing.

Twisted pair, V90-HT insulated, each pair overall Al/polyester screened with drain wire, SWA, black PVC 5V-90 sheathed.

Twisted pair or triple, V90-HT insulated, element and overall Al/polyester screened with drain wire, 5V-90 bedding, SWA, black PVC 5V-90 sheathed.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Class 5 copper conductor, 5V-90 X-90 XLPE insulated, PVC sheathed, to AS/NZS 5000.1

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Medium Multi-function Joints (MMJ) are for jointing of optical fibre cables up to 288 fibres. Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S risks and negates risk of fires. Not only are the new…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

2, 3 and 4 core plus earth circular., copper conductor, V-90 PVC insulated and 5V-90 PVC sheathed. According to AS/NZS 5000.2

It’s when the flames consume everything around them and the heat becomes intolerable that our fire-resistance cable, Firestop™, displays its best qualities. In intense heat conditions this low smoke zero halogen cable continues to supply all the critical functions such as fire alarm, emergency lighting and fans. Fully complying with the latest New Zealand standard AS/NZS 3013. This range is designed to save lives and help protect property in the event of a fire. FS110, copper conductor, Mica glass taped,…

Earth, Class 5 conductor, flexible V-90 insulated. According to AS/NZS 5000.1

Choose between high quality cables in copper or aluminium, single or three core, light or heavy duty screened, armoured or unarmoured, PVC, High Density Polyethylene or Low Smoke Zero Halogen sheathing.

This Loose tube dielectric optical cable is designed for external underground installations in ducts by pulling, jetting or floating techniques or by direct burial in open-cut trenches. The cable is designed for installation in areas where mechanical impact is expected. Two types of sheaths can be provided with the Central Loosetube Optical Cable: - UV stabilised Low Smoke Zero Halogen (LS0H), flame retardant compound in compliance with AS 1049. - UV stabilised Polyethylene (PE) in compliance with AS 1049. Two…

2 and 3 core flat TPS, copper conductor V-90, PVC insulated and 3v-90 PVC sheathed. According to AS/NZS 5000.2

Our Flexible Firestop cables not only save lives and protect property. Thanks to the flexibility you can loose your bending equipment and shorten the installation time by far. These low smoke halogen free cables fully comply with the latest New Zealand Standards.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Our long and successful experience in high voltage and EHV cable systems has led to the development of a comprehensive range of accessories for extruded dielectric cables. High voltage accessories for XLPE cables include CLICK-FIT® and Pry-Mould accessories. CLICK-FIT® The CLICK-FIT® plug-in concept is a unique system designed to connect High and Extra-High-Voltage extruded power cables for 72kV up to 420kV. Pry-Mould These accessories are based on pre-moulded electrical components, i.e. stress cones for terminations and one-piece sleeves for joints.…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Large Multi-function Joints (LMJ) are for jointing of optical fibre cables up to 1344 fibres (with option to double capacity using 24 fibre single element trays). Our new range of joints is designed to integrate state of the art features into very cost effective products. They not only save you money, but are also designed to eliminate heat shrink thus no need for a heat source in the field during installation. Using Mechanical Seals to terminate the cables lowers OH&S…

2, 3 and 4 core plus earth circular, copper conductor, V-90 PVC insulated and 5V-90 PVC sheathed. According to AS/NZS 5000.1

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

2, 3 and 4 core plus earth, copper conductor, X-90 XLPE insulated, 5V-90 PVC sheathed. According to AS/NZS 5000.1

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

3 and 4 core plus earth, copper conductor, X-90 XLPE insulated, PVC bedded, steel wire armoured, 5V-90 PVC sheathed. According to AS/NZS 5000.1

Prysmian Components offers a wide range of accessories suitable for all requirements, from simple industrial applications to hazardous areas, on and offshore. They include cable connectors and tooling, cable glands as well as cleats and cable fixings. Cable connectors and tooling We can offer a wealth of experience and expertise in the design and manufacture of power cable connectors and tooling. The range includes pre-insulated connectors plus Low and Medium Voltage connectors for both copper and aluminium. Cable glands We…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Introducing FlexTube Cables from Prysmian - Fibre density like no other! The FlexTube products offer many advantages compared with using standard loose tube optical cable. The innovative micromodule design incorporates soft, flexible fibre units - more dense and quicker to prepare and install. These key benefits of denser design and easier handling translate to major savings in terms of time and cost – and the larger the project, the greater the savings. What does FlexTube deliver? Record breaking fibre density, increasing duct…

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

In order to meet different standards and preconditions we always tailor-make the cables in this area. Please contact our experts to specify your requirements.

Accessories for power cables have a significant importance in the reliability of any cable circuit. Our product portfolio features a complete range of different designs, all available to order.

Choose between high quality cables in copper or aluminium, single or three core, light or heavy duty screened, armoured or unarmoured, PVC, High Density Polyethylene or Low Smoke Zero Halogen sheathing.

Choose between high quality cables in copper or aluminium, single or three core, light or heavy duty screened, armoured or unarmoured, PVC, High Density Polyethylene or Low Smoke Zero Halogen sheathing.